Site Logo-Fibconet

Installation of Fibconet Fiber Optic Connectors Fiber dwdm

How To Get Products In The First Time After Chinese New Year-News
1. The direct buried optical cable connector should be well placed. The optical cables reserved on both sides of the connector should be coiled or neatly coiled on both sides of the connector. 2. The optical cables at both ends of the hanging overhead optical cable connector should be telescopically bent, and the reserved optical cables at both ends should be coiled on the adjacent poles. The installation dimensions of the overhead optical connector fixed on the pole and the reserved optical cable. 3. The installation method of the pipe optical cable joint should be hung on the manhole wall or placed between the cable support plates, and should meet the following requirements: 1) Try to install it at a higher position in the manhole to avoid water immersion in the manhole during the rainy season; 2) The installation position should not affect the placement of other optical cables and cable joints in the manhole; 3) The reserved optical cable should have protective measures. 4. When the design documents have special provisions for the installation of optical cable joints, they should be implemented according to the design requirements. fibconet.com fiber dwdmfiber dwdm fiber dwdm
Installation of optical cable in office (station) Optical cable terminal in office (station) 1. According to regulations or design requirements, enough reserved optical cables should be reserved. 2. The installation position of the optical cable terminal connector in the terminal room should be stable and safe, away from the heat source. 3. The connector of the tail optical cable or single-core optical cable drawn from the optical cable terminal connector should be inserted into the optical distribution frame (distribution panel) according to the design requirements. Connectors that are temporarily not plugged into optical distribution frames (distribution panels) should be covered with plastic caps. 4. When using the optical fiber in the external optical cable to make the connector, the connection loss should meet the design requirements. The production of connectors should be strictly in accordance with process specifications. 5. The coiling of the optical fiber in the rack should be larger than the specified radius of curvature. 6. The copper wires in the optical cable should be introduced into the service disk respectively, and the remote supply service should be terminated. 7. The metal reinforcement core, shielded wire (aluminum sheath) and metal armor layer should be grounded according to the design requirements. 8. The direction and serial number of the optical fiber and copper wire should be marked in the conspicuous part. fibconet.com fiber dwdm fiber dwdm fiber dwdm
Installation of unmanned relay station 1. The chassis of the unmanned relay station should be fixed on the cement table or bracket. 2. After the optical cable is introduced into the unmanned relay, the inlet pipe hole should be blocked to prevent water seepage and leakage. 3. The unmanned relay station chassis must be checked for air tightness before installation. If the tail cable has an air-tight head, check the air-tightness of the chassis after installation. 4. The terminal connection between the optical cable and the unmanned repeater shall meet the requirements of Section 1 of this chapter. 5. The grounding protection measures for unmanned stations shall be implemented in strict accordance with the design requirements. fibconet.com Installation of unmanned relay station 1. The chassis of the unmanned relay station should be fixed on the cement table or bracket. 2. After the optical cable is introduced into the unmanned relay, the inlet pipe hole should be blocked to prevent water seepage and leakage. 3. The unmanned relay station chassis must be checked for air tightness before installation. If the tail cable has an air-tight head, check the air-tightness of the chassis after installation. 4. The terminal connection between the optical cable and the unmanned repeater shall meet the requirements of Section 1 of this chapter. 5. The grounding protection measures for unmanned stations shall be implemented in strict accordance with the design requirements. fibconet.com Installation of unmanned relay station 1. The chassis of the unmanned relay station should be fixed on the cement table or bracket. 2. After the optical cable is introduced into the unmanned relay, the inlet pipe hole should be blocked to prevent water seepage and leakage. 3. The unmanned relay station chassis must be checked for air tightness before installation. If the tail cable has an air-tight head, check the air-tightness of the chassis after installation. 4. The terminal connection between the optical cable and the unmanned repeater shall meet the requirements of Section 1 of this chapter. 5. The grounding protection measures for unmanned stations shall be implemented in strict accordance with the design requirements. fibconet.com Installation of unmanned relay station 1. The chassis of the unmanned relay station should be fixed on the cement table or bracket. 2. After the optical cable is introduced into the unmanned relay, the inlet pipe hole should be blocked to prevent water seepage and leakage. 3. The unmanned relay station chassis must be checked for air tightness before installation. If the tail cable has an air-tight head, check the air-tightness of the chassis after installation. 4. The terminal connection between the optical cable and the unmanned repeater shall meet the requirements of Section 1 of this chapter. 5. The grounding protection measures for unmanned stations shall be implemented in strict accordance with the design requirements. fibconet.com

Share:

More Posts

FTTH ABS PC Access Terminal Box Fiber Optic Distribution Box

fiber optic splitters Input splitters

Optical fiber splitter is an important device in passive optical transmission network. As a passive device, optical splitter topologically splits the input optical signal into

Get A Quick Quote

We will respond within 12 hours, please pay attention to the email with the suffix “@fibconet.com”

Also, you can go to the Contact Page, which provides a more detailed form.